Ventamatic SBV40GV User Manual
Browse online or download User Manual for Fans Ventamatic SBV40GV. Ventamatic SBV40GV User Manual
- Page / 1
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
A leader in the ventilation industry for over 60 years, Ventamatic, Ltd. oers a complete line of air movement
products for commercial, industrial, agricultural, and residential use sold under these ne names:
®
®
VENTAMATIC, LTD. P.O. BOX 728, MINERAL WELLS, TX 76068-0728 • PHONE 800-433-1626 FAX 940-325-9311 • WWW.BVC.COM • E-MAIL: BVC@BVC.COM
STATIC ATTIC VENTILATORS
INSTALLATION INSTRUCTIONS
Models: STV51, STV51GV, SBV603, SBV603GV, SBV61, SBV40GV
These roof-mounted units are designed for attics of average size and operate most eciently if air intakes are located
around the eaves. For larger attics, use two or more units. An adequate amount of air intake is required for each unit.
1. Place the unit on top of the shingles, as close to the center of the roof and as near to the
ridge line as possible. For neat installation, the low prole housing on the unit should be
visible only on one side of the roof. This will require that the unit be moved down
slightly from the ridge. When this position is established, locate a centerline directly
between two rafters and drill a hole through the roof, from the inside. This hole will be
used as a center for the following operations.
2. Draw a circle or square on the roof (refer to chart below for opening size), using the
drilled hole as the center, and cut the appropriate size hole in the roof.
3. With the top of the unit parallel to the ridge line, slide the ange up under the shingles.
It may be necessary to remove some additional roong material and fasteners around
the unit for it to t snugly. Select an appropriate roong sealant for the construction
material (refer to chart below), and apply a generous amount between the ange and
shingles, approximately ½” from the outer edge. Secure with approved roong nails, or
staples with a minimum 1” penetration, and a maximum 4” space between each nail or
staple.
LOCATING THE STATIC VENT
CUTTING THE HOLE
INSTALLING THE VENT
STV-51 / STV-51 GV Square top aluminum / galvanized 16.5” x 17.5“ 8 .125” 51 sq in
SBV 603 / SBV 603 GV Slant back aluminum / galvanized 16“ x 20” 8.125” 51 sq in
SBV61 Slant back plastic 17“ x 18” 9” 61 sq in
SBV 40 GV Slant back galvanized 14“ x 16.75” 7.25” 40 sq in
MODEL DESCRIPTION BASE OPENING NFA
STV51 SBV603 SBV61 SBV40GV
1
Summary of Contents
Page 1 - INSTALLATION INSTRUCTIONS
A leader in the ventilation industry for over 60 years, Ventamatic, Ltd. oers a complete line of air movementproducts for commercial, industrial, agr
Related products and manuals for Fans Ventamatic SBV40GV
Fans Ventamatic CX1500 User Manual
(4 pages)
(4 pages)
Fans Ventamatic CX1000 User Manual
(4 pages)
(4 pages)
Fans Ventamatic CX36BD2SPD User Manual
(8 pages)
(8 pages)
Fans Ventamatic IF12P User Manual
(1 pages)
(1 pages)
(4 pages)
Fans Ventamatic HVFF 20 User Manual
(4 pages)
(4 pages)
© 2020, manymanuals.com. All rights reserved. | 0.144 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals